CC612 Charge Controller

CC612 Charge Controller

  • Smart Grid capable via OCPP communication protocol
  • Compact design, only 22.6 mm wide
  • Supports local load management
  • PLC modem (ISO 15118) integrated
  • GFCI Type A sufficient for the charging station, GFCI Type B not required

The charge controller monitors charging system internal hardware, such as the meter, the user interface board or the socket. It is characterized by its compact design and size that in turn enables intelligent, small and cost effective charging systems. To enable the charge controller to communicate, a backend system is required. Given that most backend providers strictly adhere to the Open Charge Point Protocol (OCPP), the charge controller is OCPP 1.5 and OCPP 1.6 compliant. All specified messages in OCPP are supported as well as some vendor-specific extensions based on the DataTransfer message. Integration tests with the backend implementations of providers such as Vattenfall, Bosch, NTT and DRIIVZ have been successfully carried out. The charge controller can be operated as an “always on” system that is always connected to a mobile network. The controller supports 2.5G Edge and 4G UMTS mobile networks. Connectivity for online operation requires a SIM card (which is not included in delivery). User interaction is facilitated using an RFID module, which consists of an RFID card reader and LEDs. Charging is initiated by holding a valid RFID card close to the reader. In offline operation, the charge controller can optionally allow charging without authorization or it can authorize users based on RFID and a local white list of authorized RFID cards.

The software for controlling all processes of the charge controller can be updated. This makes the CC612 future-proof. Updates (typically quarterly) can be easily installed via USB, Ethernet or over-the-air (OTA). If a vulnerability is detected in the software, it can be reported here.

  • Features
  • Applications
  • Accessories
  • Ordering information
  • Downloads
  • Charge controller acc. to IEC 61851-22 (mode 3)
  • It can be configured as either a Master or Slave
  • The charge controller can be integrated into a single or three-phase system up to 80 A
  • Future-proof, encoded and standardised networking with EMS through the EEBUS communication protocol
  • Smart Grid enabled using standard OCPP functionality
  • OCPP 1.5 and OCPP 1.6 compliant with JSON, SOAP and Binary implementation
  • Supports 4G (LTE), 3G (UMTS) und 2G (GSM) mobile networks with an integrated 4G modem in all data gateways with 4G modem
  • Two USB interfaces:
    – CONFIG for local configuration
    – Other is used an extension port for peripheral USB devices (Ethernet/WiFi home applications)
    – Master/slave hardware configuartion
  • Control Pilot and Proximity Pilot signal management
  • Universal charge plug control (support for different vendors of sockets)
  • Configurable support for one additional household socket
  • Can connect to eHZ or Modbus meters and to meters with an S0 interface
  • User interface board for customer-specific applications
  • Configurable 3-channel input/output extension interface for additional functionality
  • Only an external RCD type A is required
  • Internal temperature sensors
  • A Peer Group Mechanism or Dynamic Load Management where a set current is shared between a group of charge controllers
  • Optional integrated ISO/IEC 15118 power line communication (PLC) for plug & charge and load management systems
  • Local and remote configuration
  • electric vehicle (EV) charging stations, wall boxes or street light charging points


Optional accessories for CC612 Charge Controller

DesignationArt. No.
RFID105-L1 with RJ45 cable (length 500 mm)B94060105
RFID114 with RJ45 cable (length 500 mm)B94060114
RFID117-L1 with RJ45 cable (length 500 mm)B94060117
Measuring Current transformer* CTBC17 (PCB variant)B98080070
Connection cable CTBC17-Cable180 incl. clip housing (cable length 180 mm)B98080540
Connection cable CTBC17-Cable325 incl. clip housing (cable length 325 mm)B98080541
Connection cable CTBC17-Cable1470 incl. clip housing (cable length 1470 mm)B98080542
DPM2x16FP (display module)B94060120
* The measuring current transformer has an internal diameter of 17 mm.

Variants of CC612 Charge Controller

TypeModemMeterRDC-MD*PLC** hardwareUser interfaceLEDs Art. No.
CC612-1M4PR4GeHZ-, S0 interfaceReady, Alarm, PLCB94060011
CC612-2M4PR4GModbus, S0 interfaceReady, Alarm, PLCB94060013
CC612-2M4R4GModbus, S0 interface--Ready, AlarmB94060015
CC612-1S0PR--eHZ-, S0 interfaceReady, Alarm, PLCB94060005
CC612-2S0PR--Modbus, S0 interfaceReady, Alarm, PLCB94060007
CC612-2S0R--Modbus, S0 interface--Ready, AlarmB94060010
*The charge controller only works in combination with the measuring current transformer, which must be ordered separately.
** Optional and enabled by a software update

Downloads for CC612 Charge Controller



Category Product Language Size Download